ELASTOPHENE FLAM 25 PDF

ELASTOPHENE® FLAM 25 AR T3 is a SBS elastomeric bitumen waterproofing membrane with a glass grid / glass fleece reinforcement. The topside is protected . ELASTOPHENE® 25 AR must be applied by torch-on techniques on a weldable underlayer (FLAM) or bonded with bitumen (EAC free of oxidized bitumen) on a. ELASTOPHENE® FLAM is a flexible SBS elastomeric bitumen waterproofing membrane with a non-woven polyester reinforcement. Both sides are.

Author: Takinos Akizil
Country: Gabon
Language: English (Spanish)
Genre: Marketing
Published (Last): 1 August 2012
Pages: 142
PDF File Size: 8.20 Mb
ePub File Size: 16.71 Mb
ISBN: 320-2-30979-444-7
Downloads: 95861
Price: Free* [*Free Regsitration Required]
Uploader: Fenrisho

Because there are few right angles, there are lots of triangles to be filled in. Before the insulation is laid, the channels carrying the rain water are reinforced: This second layer of bitumen should be placed on the Knauf Thane ET within a few hours to ensure that the Sopracolle glue speads out under the pressure of the layer of bitumen above.

If there is a risk of rain, then the Knauf Thane ET glued to the first layer must be elasotphene enclosed by the second layer, even if this means performing work not needed by the final waterproofing.

ELASTOPHENE FLAM 180-25

Finishing around rain water collector See 2. On my roof, the rolls of the final layer are positioned north-south, so the second layer must be east-west. These are ajusted now but will be fitted later taking into account the future height of the finished surface.

  74HC192 DATASHEET PDF

The weekend brings heavy rain to test the waterproofing — not a drop gets through to the house. Finition autour de la platine. Cinq points de Sopracolle par plaque.

ELASTOPHENE® 25 AR – Soprema

The two layers should be perpendicular to one another. Il est bien plus elastpohene de remplacer les renforts par le flashing: Applying the insulation requires careful attention to the weather forecast and the planning of the work.

For example the first layer could be omitted, and the insulation glued directly to the existing surface. Soudage du renfort sur platine et dalle. The first layer, which provides the waterproofing, is of elastic bitumen, 2. The joint of the flat roof and the rising walls that surround the roof are a possible source of leaks.

The orientation of the second layer depends on the way in which the third layer will be applied. Rodolphe Ferracane, e-mail contact AFR-etancheite. The collector is trimmed before applying the outer reinforcement. The rain water collector will pass through this. Chauffage du sur-renfort et de la platine.

ELASTOPHENE® 25

Heating the outer-reinforcement and the collector. La partie bitume fait approximativement 2. Click on photo to enlarge. Good waterproofing requires a reinforcing piece between the roof and the elastopheje. Cutting nord end of a roll of finishing layer. The photos on this page describe the work. Cliquer sur les photos pour les agrandir. Reinforcement at junction of standups.

  LUIS TORGO PDF

ELASTOPHENE FLAM | SOPREMA

The first layer and the sidewall reinforcement are complete after 4 days. The second bitumous layer is of the same material as the first. The work specified by this standard is often referred to as Three layers plus insulation, with heated reinforcement. Click on figure to enlarge. As with the 1st layer, the joint of the flat roof and the rising walls that surround the roof are a possible source of leaks.

Click on the photos to enlarge them. Welding the outer reinforcement onto the collector.

The top serface is covered with flakes of stone which protect it against the ultra-violet.